Renault Clio: Exhaust gas recirculation solenoid valve: Removal - Refitting

Renault Clio III (2005-2013) Service Manual / Engine And Peripherals / Antipollution / Exhaust gas recirculation solenoid valve: Removal - Refitting

K9K, and 764 or 766 or 768

Renault Clio. Exhaust gas recirculation solenoid valve: Removal - Refitting

REMOVAL

I - REMOVAL PREPARATION OPERATION

K9K, and 766 or 768

Renault Clio. Exhaust gas recirculation solenoid valve: Removal - Refitting

K9K, and 764

Renault Clio. Exhaust gas recirculation solenoid valve: Removal - Refitting

II - REMOVAL OF PART CONCERNED

Renault Clio. Exhaust gas recirculation solenoid valve: Removal - Refitting

Note: During removal of the solenoid valve using the (Mot. 1729), proceed slowly until the solenoid valve is loosened from its support to remove it.

REFITTING

I - REFITTING PREPARATION OPERATION

II - REFITTING PART CONCERNED

III - FINAL OPERATION

K9K, and 764

 

Note: If replacing the exhaust gas recirculation solenoid valve, perform the necessary programming (see MR394, Section 13B, Fault finding - Replacement of components).

K9K, and 750 or 752

Renault Clio. Exhaust gas recirculation solenoid valve: Removal - Refitting

REMOVAL

I - REMOVAL PREPARATION OPERATION

II - OPERATION FOR REMOVAL OF PART CONCERNED

Renault Clio. Exhaust gas recirculation solenoid valve: Removal - Refitting

Note: Clean the exhaust gas recirculation solenoid valve if it is reinitialised (see Exhaust gas recirculation solenoid valve: Cleaning) (Technical Note 3916A, 14A, Emission control).

REFITTING

I - REFITTING PREPARATION OPERATION

II - REFITTING OPERATION FOR PART CONCERNED

III - FINAL OPERATION

Note: If replacing the exhaust gas recirculation solenoid valve, perform the necessary programming (see MR394, Section 13B, Fault finding - Replacement of components).

READ NEXT:

 Exhaust gas cooler: Removal - Refitting

K9K, and 764 or 766 or 768 or 772 REMOVAL I - REMOVAL PREPARATION OPERATION Position the vehicle on a two-post lift (see Vehicle: Towing and lifting) (MR 392, 02A, Lifting equipment). Disconnect

 Exhaust gas recirculation unit: Removal - Refitting

K9K, and 750 or 752 REMOVAL Position the vehicle on a two-post lift. Remove the scuttle panel grille (see Scuttle panel grille: Removal - Refitting). Disconnect the exhaust gas recirculation

 Exhaust gas recirculation mounting: Removal - Refitting

K9K, and 764 or 766 or 768 To remove/refit the exhaust gas recirculation mountings (see 14A, Antipollution, Exhaust gas cooler: Removal - Refitting, 14A-7). K9K, and 750 or 752 REMOVAL I - REMOVAL P

SEE MORE:

 To refit a wheel

A wheel size larger than 15” cannot be installed under the vehicle. To carry out this operation, the cable must be unwound. If the cable has been wound back up on its own, unwind it again as follows: pull the handle to unwind the cable; press the button located u

 Additional methods of restraint

All of the warnings below are given so that the airbag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when it inflates. The airbag is designed to complement the action of the seat belt. Both th

© 2016-2025 Copyright Renault Clio Owners Club