Renault Clio: Engagement sensor: Removal - Refitting
Renault Clio III (2005-2013) Service Manual / Transmission / Sequential Gearbox / Engagement sensor: Removal - Refitting
K9K, and JA5
REMOVAL
I - REMOVAL PREPARATION OPERATION
- Position the vehicle on a two-post lift (see Vehicle: Towing and lifting) (MR 392, 02A, Lifting equipment).
- Disconnect the battery (see Battery: Removal - Refitting) (MR 392, 80A, Battery).
- Remove the front left-hand wheel (see Wheel: Removal - Refitting) (MR 392, 35A, Wheels and tyres).
II - OPERATION FOR REMOVAL OF PART CONCERNED
- Disconnect the engagement sensor connector.
- Remove:
- the engagement sensor bolts,
- the engagement sensor (1).
REFITTING
I - REFITTING OPERATION FOR PART CONCERNED
- Refit:
- the engagement sensor,
- the engagement sensor bolts.
- Tighten to torque the engagement sensor bolts (4 Nm).
- Connect the engagement sensor connector.
II - FINAL OPERATION.
- Connect the battery (see Battery: Removal - Refitting) (MR 392, 80A, Battery).
- Refit the front left-hand wheel (see Wheel: Removal - Refitting) (MR 392, 35A, Wheels and tyres).
- Carry out the necessary programming (see Fault finding - Replacement of components) (MR 394, 21B, Sequential gearbox).
WARNING
After the accumulator has been fully filled (15 seconds after the ignition has been switched on): the oil is at the MIN mark.
D4F, and JA3
REMOVAL
I - REMOVAL PREPARATION OPERATION
- Position the vehicle on a two-post lift (see Vehicle: Towing and lifting) (MR 392, 02A, Lifting equipment).
- Disconnect the battery (see Battery: Removal - Refitting) (MR 392, 80A, Battery).
- Remove the front left-hand wheel (see Wheel: Removal - Refitting) (MR 392, 35A, Wheels and tyres).
II - OPERATION FOR REMOVAL OF PART CONCERNED
- Disconnect the engagement sensor connector.
- Remove:
- the engagement sensor bolts,
- the engagement sensor (1).
REFITTING
I - REFITTING OPERATION FOR PART CONCERNED
- Refit:
- the engagement sensor,
- the engagement sensor bolts.
- Tighten to torque the engagement sensor bolts (4 Nm).
- Connect the engagement sensor connector.
II - FINAL OPERATION.
- Connect the battery (see Battery: Removal - Refitting) (MR 392, 80A, Battery).
- Refit the front left-hand wheel (see Wheel: Removal - Refitting) (MR 392, 35A, Wheels and tyres).
- Carry out the necessary programming (see Fault finding - Replacement of components) (MR 394, 21B, Sequential gearbox).
WARNING
After the accumulator has been fully filled (15 seconds after the ignition has been switched on): the oil is at the MIN mark.
READ NEXT:
Actuator module: Removal - Refitting
K9K, and JA5
(1) Clutch solenoid valve
(2) Gear engagement solenoid
valve
(18) Gear engagement solenoid
valve
(4) Selection solenoid valve
(5) Engagement sensor
(20) Gear selection sensor
(7) Solen
Gear selection sensor: Removal - Refitting
K9K, and JA5
REMOVAL
I - REMOVAL PREPARATION OPERATION
WARNING
To remove the gear selection sensor it is essential
that you shift to first gear before removal.
Remove:
the battery (see Battery: R
Clutch position sensor: Removal - Refitting
K9K, and JA5
REMOVAL
I - REMOVAL PREPARATION OPERATION
Position the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 392, 02A, Lifting equipment).
Disconnect the battery (see Batte
SEE MORE:
Radiator mounting cross member: General description
Note:
The information contained in the following
describes the general repair procedure for all vehicles
having the same design for this part.
Before reading this general information, check that
there are no special notes associated with this vehicle.
These special notes will be specified if appli
K9K, and 764 or 772
IMPORTANT
Wear protective gloves during the operation.
WARNING
Never rotate the engine anti-clockwise (timing end).
WARNING
Do not run the engine without the accessories belt,
to avoid breaking the crankshaft accessories pulley.
PARTS AND CONSUMABLES FOR THE
REPAIR WORK
Parts always to be replace
© 2016-2025 Copyright Renault Clio Owners Club
