Renault Clio: Headlight: Removal - Refitting
DISCHARGE LAMPS, and DOCUMENTATION
PHASE 1
IMPORTANT
To prevent eye injuries:
- do not look at a xenon bulb when lit (voltage
when lit 20000 V),
- do not light a bulb which has not been fitted into
its headlight.
IMPORTANT
To prevent burns, wait until the " computers -
power unit " assemblies are cold before removal.
REMOVAL
I - REMOVAL PREPARATION OPERATION
- Position the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
DISCHARGE LAMPS, and DOCUMENTATION
PHASE 1
- Disconnect the battery (see 80A, Battery, Battery:
Removal - Refitting, 80A-1).
- Remove:
- the front wheels (see Wheel: Removal - Refitting)
(35A, Wheels and tyres),
- the front section of the front wheel arch liners (see
Front wheel arch liner: Removal - Refitting)
(55A, Exterior protection),
- the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection).
II - OPERATION FOR REMOVAL OF PART
CONCERNED
DOCUMENTATION PHASE 1

- Remove the upper bolts (1) from the headlight.

- Remove:
- the headlight lower bolt (2),
- the plastic rivet (3).
DOCUMENTATION PHASE 2

- Remove the upper bolts (4) from the headlight.

- Remove the lower bolts (5) from the headlight.
- Remove the headlight.
- Disconnect the headlight connectors.
- Remove the headlight.
REFITTING
I - REFITTING OPERATION FOR PART
CONCERNED
- Connect the headlight connectors
- Refit the headlight.
II - FINAL OPERATION
DISCHARGE LAMPS, and DOCUMENTATION
PHASE 1
- Connect the battery (see 80A, Battery, Battery: Removal
- Refitting, 80A-1).
- Adjust the headlights (see 80B, Headlights, Headlight:
Adjustment, 80B-9).
- Refit:
- the front bumper (see Front bumper: Removal -
Refitting) (55A, Exterior protection),
- the front section of the front wheel arch liners (see
Front wheel arch liner: Removal - Refitting)
(55A, Exterior protection),
- the front wheels (see Wheel: Removal - Refitting)
(35A, Wheels and tyres).
READ NEXT:
DOCUMENTATION PHASE 1
ADJUSTMENT
I - PREPARATION OPERATION FOR CHECK
Place the vehicle in a working area equipped with a
two-post lift.
Note:
Check that the lift is on flat, horizontal ground.
DOCUMENTATION PHASE 1
REMOVAL
DISCHARGE LAMPS
IMPORTANT
To prevent eye injuries:
do not look at a xenon bulb when lit (voltage
when lit 20000 V),
do not light a bulb which has not been fitted into
DOCUMENTATION PHASE 1
DISCHARGE LAMPS
IMPORTANT
To prevent burns, wait until the " computers -
power unit " assemblies are cold before removal.
IMPORTANT
To prevent eye injuries:
do not look at a xe
SEE MORE:
K9K - D4F, and 784 or 786
Note:
Vehicles equipped with the K9K*768 engine may or
may not be equipped with an intercooler.
REMOVAL
I - REMOVAL PREPARATION OPERATION
Position the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (02A, Lifting equipment).
Remove:
the front wheel arch
EQUIPMENT LEVEL E3 LEISURE or EQUIPMENT
LEVEL EA1 or EQUIPMENT LEVEL EA2 or
EQUIPMENT LEVEL EA3 or EQUIPMENT LEVEL
EA4 or EQUIPMENT LEVEL EA5 or EQUIPMENT
LEVEL EAG
Diameter of the anti-roll bar: 20.5 mm.
EQUIPMENT LEVEL EAC or EQUIPMENT LEVEL
SPORT
Diameter of the anti-roll bar: 19.5 mm.
REM
© 2016-2025 Copyright Renault Clio Owners Club
