Renault Clio: F4R, and Left-hand Drive

REMOVAL
I - REMOVAL PREPARATION OPERATION
- Position the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 392, 02A, Lifting equipment).

- Remove:
- the battery (see Battery: Removal - Refitting)
(MR 392, 80A, Battery),
- the air filter unit (see Air filter unit: Removal - Refitting)
(MR 392, 12A, Fuel mixture),
- the non-return valve (1) from the servo,
- the master cylinder (see 37A, Mechanical component
controls, Master cylinder: Removal - Refitting, 37A-2),

- Remove the side panel (12).


- Remove:
- the bolts (2),
- the clip (3).
- the lower cover (4), disconnecting the various connectors.
II - OPERATION FOR REMOVAL OF PART
CONCERNED

- Remove:
- the double safety connecting shaft (5) from between
the brake servo pushrod and the brake pedal,
and, after tilting the connecting shaft upwards,
move ring (6) using a flat-blade screwdriver.
- the connector (7) from the accelerator pedal,
- the accelerator pedal connector wiring harness
clip,
- the blanking cover (8) from the brake servo mounting
nut,
- the brake servo mounting nuts (9),
- the brake servo.

- Remove:
- the mounting bolts (10) from the brake servo spacer,
- the brake servo spacer.
REFITTING
I - REFITTING PREPARATIONS OPERATION

- Check that the brake servo seal (11) is present; replace
the seal if it is faulty.
- The shaft connecting the brake servo pushrod and
the brake pedal must be replaced every time it is removed.

- Check the following dimension before refitting: (X1)
= 171 mm.
II - REFITTING OPERATION FOR PART
CONCERNED
- Refit:
- the brake servo spacer,
- the brake servo spacer mounting bolts.
- Torque tighten the spacer mounting bolts (21
Nm).
- Refit:
- the brake servo,
- the brake servo mounting nuts.
- The shaft connecting the brake servo pushrod and
the brake pedal must be refitted from right to left,
and from top to bottom.
- Torque tighten the brake servo mounting nuts (21
Nm).
- Refit:
- the brake servo mounting nut blanking cover,
- the accelerator pedal connector wiring harness
clip,
- the accelerator pedal connector,
- the double safety connecting piece between the
brake servo pushrod and the brake pedal.
III - FINAL OPERATION.
- Refit:
- the lower cover, connecting the various connectors.
- the clip,
- the bolts,
- the dashboard trim piece
- the dashboard side panel,
- the master cylinder (see 37A, Mechanical component
controls, Master cylinder: Removal - Refitting, 37A-2),
- the air filter unit (see Air filter unit: Removal - Refitting)
(MR 392, 12A, Fuel mixture),
- the battery (see Battery: Removal - Refitting)
(MR 392, 80A, Battery).
- Connect the non-return valve on the servo,
- Bleed the brake circuit (see 30A, General information,
Braking circuit: Bleed, 30A-4).
IMPORTANT
Check that the brake servo pushrod-brake pedal
connecting shaft is locked in place.
- Adjust the brake light switch (see 37A, Mechanical
component controls, Brake pedal switch: Removal
- Refitting, 37A-79).
READ NEXT:
REMOVAL
I - REMOVAL PREPARATION OPERATION
Position the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 392, 02A, Lifting equipment).
Disconnect the battery (see Battery: Removal
REMOVAL
I - REMOVAL PREPARATION OPERATION
Position the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 392, 02A, Lifting equipment).
Disconnect the battery (see Battery: Removal
REMOVAL
I - REMOVAL PREPARATION OPERATION
Remove the dashboard side face (1).
Remove:
the protective strips from the lower cover (2),
the bolts (3),
the lower cover (4), disconnecting th
SEE MORE:
USING THE DASHBOARD CROSS MEMBER
REMOVAL TOOL Car. 1765
Use this tool as indicated in the dashboard removal
procedure.
Fit the tool Car. 1765 as far as the stop (10).
Screw the rod (11) onto the body (10) as far as the
stop.
Firmly lock tool body in the same way as a lock nut
against th
Front side door: Removal - Refitting
I - REMOVAL WITHOUT HINGES
1 - REMOVAL PREPARATION OPERATION
Disconnect the door wiring harness supply connector.
2 - OPERATION FOR REMOVAL OF PART
CONCERNED
Remove:
the door mounting nuts (1),
the door.
II - REFITTING WITHOUT HINGES
1 - OPERATION
© 2016-2025 Copyright Renault Clio Owners Club
