Renault Clio: Engagement sensor: Removal - Refitting
Renault Clio III (2005-2013) Service Manual / Transmission / Sequential Gearbox / Engagement sensor: Removal - Refitting
K9K, and JA5
REMOVAL
I - REMOVAL PREPARATION OPERATION
- Position the vehicle on a two-post lift (see Vehicle: Towing and lifting) (MR 392, 02A, Lifting equipment).
- Disconnect the battery (see Battery: Removal - Refitting) (MR 392, 80A, Battery).
- Remove the front left-hand wheel (see Wheel: Removal - Refitting) (MR 392, 35A, Wheels and tyres).
II - OPERATION FOR REMOVAL OF PART CONCERNED
- Disconnect the engagement sensor connector.
- Remove:
- the engagement sensor bolts,
- the engagement sensor (1).
REFITTING
I - REFITTING OPERATION FOR PART CONCERNED
- Refit:
- the engagement sensor,
- the engagement sensor bolts.
- Tighten to torque the engagement sensor bolts (4 Nm).
- Connect the engagement sensor connector.
II - FINAL OPERATION.
- Connect the battery (see Battery: Removal - Refitting) (MR 392, 80A, Battery).
- Refit the front left-hand wheel (see Wheel: Removal - Refitting) (MR 392, 35A, Wheels and tyres).
- Carry out the necessary programming (see Fault finding - Replacement of components) (MR 394, 21B, Sequential gearbox).
WARNING
After the accumulator has been fully filled (15 seconds after the ignition has been switched on): the oil is at the MIN mark.
D4F, and JA3
REMOVAL
I - REMOVAL PREPARATION OPERATION
- Position the vehicle on a two-post lift (see Vehicle: Towing and lifting) (MR 392, 02A, Lifting equipment).
- Disconnect the battery (see Battery: Removal - Refitting) (MR 392, 80A, Battery).
- Remove the front left-hand wheel (see Wheel: Removal - Refitting) (MR 392, 35A, Wheels and tyres).
II - OPERATION FOR REMOVAL OF PART CONCERNED
- Disconnect the engagement sensor connector.
- Remove:
- the engagement sensor bolts,
- the engagement sensor (1).
REFITTING
I - REFITTING OPERATION FOR PART CONCERNED
- Refit:
- the engagement sensor,
- the engagement sensor bolts.
- Tighten to torque the engagement sensor bolts (4 Nm).
- Connect the engagement sensor connector.
II - FINAL OPERATION.
- Connect the battery (see Battery: Removal - Refitting) (MR 392, 80A, Battery).
- Refit the front left-hand wheel (see Wheel: Removal - Refitting) (MR 392, 35A, Wheels and tyres).
- Carry out the necessary programming (see Fault finding - Replacement of components) (MR 394, 21B, Sequential gearbox).
WARNING
After the accumulator has been fully filled (15 seconds after the ignition has been switched on): the oil is at the MIN mark.
READ NEXT:
Actuator module: Removal - Refitting
K9K, and JA5
(1) Clutch solenoid valve
(2) Gear engagement solenoid
valve
(18) Gear engagement solenoid
valve
(4) Selection solenoid valve
(5) Engagement sensor
(20) Gear selection sensor
(7) Solen
Gear selection sensor: Removal - Refitting
K9K, and JA5
REMOVAL
I - REMOVAL PREPARATION OPERATION
WARNING
To remove the gear selection sensor it is essential
that you shift to first gear before removal.
Remove:
the battery (see Battery: R
Clutch position sensor: Removal - Refitting
K9K, and JA5
REMOVAL
I - REMOVAL PREPARATION OPERATION
Position the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR 392, 02A, Lifting equipment).
Disconnect the battery (see Batte
SEE MORE:
Engine oil level: general information
It is normal for an engine to use oil for
lubrication and cooling of moving parts
and it is normal to top up the level between
oil changes.
However, contact your approved
Dealer if more than 0.5 litres is being
consumed every 600 miles (1,000 km)
after the running in period.
Oil change f
Master cylinder: Removal - Refitting
F4R or K4J or K4M or K9K or M4R, and LEFT-HAND DRIVE
WARNING
Prepare for brake fluid outflow, to prevent damage
to the mechanical parts and bodywork around the
braking system.
REMOVAL
I - REMOVAL PREPARATION OPERATION
Position the vehicle on a two-post lift (see Vehicle:
Towing and lifting) (MR
© 2016-2025 Copyright Renault Clio Owners Club
