Renault Clio: Rear pyrotechnic inertia reel: Removal - Refitting
B85 or C85 or K85
IMPORTANT
Consult the safety and cleanliness advice and operation
recommendations before carrying out any
repair (see 88C, Air bag and Pretensioners, Airbag
and pretensioners: Precautions for the
repair, 88C-6).
REMOVAL
I - REMOVAL PREPARATION OPERATION
IMPORTANT
It is essential to lock the airbag computer using
the Diagnostic tool before starting the removal.
When this function is activated, all the trigger
lines are inhibited and the airbag warning light on
the instrument panel is lit continuously (ignition
on).
IMPORTANT
Handling pyrotechnic systems (airbags or pretensioners)
near to a source of heat or flame is not
permitted: there is a risk of triggering the airbags
or pretensioners.
- Lock the airbag computer (see Fault finding - Replacement
of components) (MR 394, 88C, Airbags
and seat belt pretensioners).
- Disconnect the battery (see 80A, Battery, Battery:
Removal - Refitting, 80A-1).
- Remove the rear bench seat (see Single unit rear
bench seatback: Removal - Refitting) or (see 1/3
and 2/3 rear bench seatback: Removal - Refitting)
(MR 393, 76A, Rear seat frames and runners).
B85 or K85
- Remove the rear door sill upper lining (see Rear inner
sill upper trim: Removal - Refitting) (MR 393,
71A, Body internal trim).
C85
- Remove the rear wing panel trim (see Rear panel
lining: Removal - Refitting) (MR 393, 71A, Body
internal trim).
- Remove the rear quarter panel trim (see Quarter
panel trim: Removal - Refitting) (MR 393, 71A,
Body internal trim).
II - OPERATION FOR REMOVAL OF PART
CONCERNED
- Remove the belt's lower mounting bolt.
- Remove the seat belt upper mounting bolt (1).
- Disconnect the connector (2) from the pyrotechnic
inertia reel.
- Remove:
- the mounting bolt (3) from the inertia reel,
- the pyrotechnic inertia reel.
REFITTING
I - REFITTING PREPARATION OPERATION
- Always replace the mounting bolt for the pyrotechnic
inertia reel.
IMPORTANT
After a seat belt pyrotechnic component is triggered,
it is essential to replace certain parts.
(see Airbag and pretensioners: Precautions
for repair) (88C, Airbags and pretensioners).
II - REFITTING OPERATION FOR PART
CONCERNED
- Refit the reel.
- Torque tighten the inertia reel mounting bolt (21
Nm).
- Connect the inertia reel connector.
- Torque tighten the seat belt upper mounting bolt
(21 Nm).
- Torque tighten the seat belt lower mounting bolt
(21 Nm).
III - FINAL OPERATION.
- Refit the rear quarter panel trim (see Quarter panel
trim: Removal - Refitting) (MR 393, 71A, Body internal
trim).
B85 or K85
- Refit the rear door sill upper lining (see Rear inner
sill upper trim: Removal - Refitting) (MR 393,
71A, Body internal trim).
C85
- Refit the rear wing panel trim (see Rear panel lining:
Removal - Refitting) (MR 393, 71A, Body internal
trim).
- Refit the rear bench seat (see Single unit rear
bench seatback: Removal - Refitting) or (see 1/3
and 2/3 rear bench seatback: Removal - Refitting)
(MR 393, 76A, Rear seat frames and runners).
- Connect the battery (see 80A, Battery, Battery: Removal
- Refitting, 80A-1).
IMPORTANT
Check the airbag computer using the Diagnostic
tool. Any failure to follow these instructions may
lead to system malfunctions, or even result in the
accidental triggering of the airbags.
- If all is correct, unlock the airbag computer (see
Fault finding - Replacement of components) (MR
394, 88C, Airbags and seat belt pretensioners).
IMPORTANT
Do not reuse the pyrotechnic components. The
pretensioners or airbags on a vehicle which is to
be scrapped must be destroyed.
READ NEXT:
IMPORTANT
Consult the safety and cleanliness advice and operation
recommendations before carrying out any
repair (see 88C, Air bag and Pretensioners, Airbag
and pretensioners: Precautions for the
rep
IMPORTANT
Consult the safety and cleanliness advice and operation
recommendations before carrying out any
repair (see 88C, Air bag and Pretensioners, Airbag
and pretensioners: Precautions for the
rep
The front chest level side air bag is mounted on the
back of each front seat at the door side.
When it inflates, the airbag tears open the cover of the
module and the foam and unclips the seat cover
SEE MORE:
On vehicles fitted with this function,
control A allows you to adjust the height
of the beams according to the load.
Turn control A downwards to lower the
headlights and upwards to raise them.
If driving on the left in a left-hand
drive vehicle (or vice versa), drivers
must h
Detach the turbocharger front temperature sensor
wiring harness on the injector rail protector mounting.
Remove:
the injector rail protector mounting bolts (13),
the injector rail protector support.
Disconnect:
the damper valve connector (14) (if equipped),
the camshaft position
© 2016-2024 Copyright Renault Clio Owners Club